How to Hang a Poster Without a Frame

Nov 16, 2026
How to Hang a Poster Without a Frame

A frame costs more than the print. If the poster is temporary, or the wall is rented, there are better options. These five methods work, and they are ordered by how much they respect your wall.

1. Poster strips (best all-rounder)

Command-style poster strips are removable adhesive tabs. Two strips hold an A2 poster; four hold A1. They come off cleanly if you pull the tab straight down rather than out.

  • Holds: months to years indoors
  • Wall damage: none on painted plaster if removed correctly
  • Cost: a few pounds for a pack

The trick is to press the strip to the wall for 30 seconds before hanging, and to wait an hour before adding weight. Most failures come from hanging immediately.

2. Binder clips and pins

Two binder clips on the top edge, hung from two pins or small nails, hold a paper poster flat and let you swap it without new holes.

This works well for thick posters and for grids you have taped together, because the clip spreads the load across the join instead of pulling on one sheet.

3. Magnetic strips

A magnetic strip screwed or glued to the wall, with a second strip on the front of the poster, holds paper without piercing it. Useful for posters you rotate often, such as classroom displays.

Cheap magnetic tape is too weak for anything above A3. Look for neodymium strips rated at 1 kg or more.

4. Tape, done properly

Ordinary masking tape will peel paint. Ordinary double-sided tape will take a layer of plaster with it. Two tapes avoid both problems:

  • Painter's tape on the wall, with double-sided tape between the painter's tape and the poster. The painter's tape takes the strain and releases cleanly.
  • Washi tape across the corners, which is designed to peel off paper and painted surfaces without residue.

Never put double-sided tape directly on emulsion paint in a rented flat. The bond is stronger than the paint.

5. A wooden batten

For a large poster, a thin batten screwed to the wall above the poster, with the poster stapled to the batten, holds weight that no adhesive will. Two screws, one batten, and the poster hangs like a scroll.

This is the only method here that reliably holds a 1 m wide tiled poster without sagging in the middle.

Making a tiled poster look like one piece

If your poster is assembled from A4 sheets, the joins are the weak point. Three things help:

  1. Tape the back, not the front. Butt the sheets edge to edge and run acid-free tape along the seam on the reverse. The front stays clean.
  2. Work on the floor. Assemble and tape the whole grid flat before lifting it. A tiled poster lifted while half-taped will fold at the seams.
  3. Hang from the top edge only. Supporting the bottom as well forces the paper to buckle as humidity changes.

What not to do

  • Blu Tack on new paint. It leaves an oil mark that shows through the next coat.
  • Nails through the print. One tear and the poster is done.
  • Spray adhesive indoors. The overspray settles on everything within two metres.
  • Tape on wallpaper. Wallpaper releases far more easily than paint, and a repair is a redecoration.

If the wall is the problem

Rendered walls, textured plaster and brick defeat most adhesives. In that case, hang from a picture rail, use a freestanding poster stand, or lean the poster on a shelf and skip the wall entirely.

A note on weight

Paper is heavier than it looks. Nine A4 sheets at 160 g/m² weigh about 100 g, plus tape. That is light enough for poster strips. Sixteen sheets on A3 card can reach 500 g, which needs a batten or clips on pins.

Ready to print the poster first? Make a poster and the PDF includes a numbered assembly guide, so the grid goes together in the right order.

Imagen a Poster

Imagen a Poster

How to Hang a Poster Without a Frame | Poster Printing Guides — Imagen a Poster